1

What changes should I make to the EZ-Bridge when changing to a Multipoint system?


The EZ-Bridge ships from the factory configured as a Point-to-Point system. Sometimes people need to create a multipoint system where there is one Access Point and multiple client antennas. One application might be connecting several buildings...

Can the EZ-Bridge® be used with VLANs?


The EZ-Bridge® creates a layer 2 bridge between two points. The EZ-Bridge® will pass all VLAN packets. The new TyconOS firmware supports assigning the bridge to a particular VLAN in the user interface.

How can I setup a Repeater on an EZ-Bridge LT or LT+ running WISPOS software?


Setting up a repeater is relatively easy. It is used when you have three or more units and the third unit cannot communicate well with the main Access Point, so you set the intermediate unit as a repeater. This is useful when you need to go...

How Can I Determine If My EZ-Bridge Antenna System is Working?


There are different ways on checking if your EZ Bridge is working. After following the instruction manual on setting up the EZ Bridge, you may check if the EZ Bridge is working by: Checking the LED lights at the bottom of the antenna, if the...

How do I use the EZ Bridge as a Wi-Fi access point?


If you need wireless access at the main building: Start by making changes on the remote unit (Unit B). Switch the mode from “Station (WDS)” to “Station”. Do this by going to: Network >> Wi-Fi >> Edit >> Scroll...

My TyconOS/Ultra Discovery Tool Does Not Run!


The TyconOS and the Ultra Discovery Tool needs Java installed on your computer in order for it to run. Please download the latest version of Java on their official website "https://java.com/en/" Once you've installed Java you should be able...

What if my EZ-Bridge LT+ is bricked? Can I recover it via TFTP?


Loading EZ-Bridge LT+ TyconOS GEN 3 Firmware Via TFTP Please make sure the EZ-Bridge Unit (powered off) is connected to your PC or your network via a LAN cable. NOTE 1: Gigabit Ethernet is currently not supported by the EZ-Bridge LT+. If your...

Best method/procedure to follow for first time installs of the EZ-Bridge?


Startup Procedure Flow Chart: https://tsi.tyconsystems.com/doc/WhitePapers/Tycon Wireless White Paper - EZ-Bridge Initial Setup Procedure.pdf

What changes are required to the EZ-Bridge setup to get the system up and running?


Please be aware that no changes are required to get the units running and create a wireless bridge. All that is needed is to power the units up. They will connect automatically. We strongly recommend that you make no changes to the unit’s...

My EZ-Bridge was working but now it keeps dropping connection or performance has degraded. What could be the problem?


If your system was working but now seems to be sluggish or it is dropping connection, the most likely culprit is that some new wireless device was added in your environment and there is wireless interference causing the issue. The EZ-Bridge...

How Do I Download and Install the Discovery Tool?


To run the discovery tool, first, you need to have Java installed on your computer. Download Java from here:  "https://www.java.com/en/" Run the java installation file and follow the prompts on the installation wizard. Once you have Java...

How do I set a Static IP address on my EZ Bridge Antenna?


You may set a static IP address on an antenna by going to its web interface. Go to: Network >> Interfaces >> LAN (section) >> Edit Here are some tips on setting up a static IP address on your EZ Bridge Antenna on a private...

Will the EZ-Bridge work with my Linksys, D-link, router etc.?


The EZ-Bridge® works with all home and business routers and switches.

How do I access the EZ Bridge's Web Interface?


You can access the EZ Bridge's web interface by going to its IP address. By default, the EZ Bridges are set as DHCP clients, meaning they will be assigned an IP address automatically by your router or DHCP server. If for any reason the EZ...

How do I set up the EZ Bridge?


https://tsi.tyconsystems.com/doc/WhitePapers/Tycon Wireless White Paper - EZ-Bridge Initial Setup Procedure.pdf EZ-Bridge ®- LT+ Series Initial Set-Up Procedure and Checklist Thank you for choosing the EZ-Bridge® Wireless Antenna...

Can I Use the Second Ethernet Port to Link 2 Separate Access Points Together?


The two ethernet ports under the antenna can accept 12-24V PoE. They are used to power on the antenna. They will not provide any PoE out. The two ports also act like a switch. A device connected to the spare ethernet port will connect to the same...

How to change the transmit channel on an EZ-Bridge Ultra?


To Change transmitter frequency, open the Unit A Access Point Web Control Panel. Navigate to Wireless tab and change frequency to a fixed frequency rather than "Auto". The Unit B Client will follow automatically after a few minutes.

How do I turn on ping watchdog to automatically reboot the EZ-Bridge Ultra antennas?


Navigate to the Services Page. Enable Ping Watchdog and enter the IP address of the other antenna into the "IP Address to ping" field. Do this for both antennas. The result will be if the antennas lose connection with each other, they will...

How many IP Cameras can I use with my EZ-Bridge LT2+ or LT5+ wireless link?


The EZ-Bridge LT+ can support up to 100Mbps bandwidth. Normally people will see around 80Mbps due to RF interference or electrical noise or multipath issues which cause packet retries and affect the overall throughput across the wireless...

How can I secure SSH and Telnet on the EZ-Bridge


If you want to tighten the security of accessing the EZ-Bridge unit through a terminal program like SSH or Telnet, we recommend the following: Set the listening port to a custom port. Any port other than 22 or 23 would work. We suggest port...

How to adjust multiple bridges distance optimization


Using 1 Side A and have it connected to the 2 remote units to eliminate interference from 1 side to the other.    First thing you need to do is to make sure both remote devices have the same SSID  as the AP you are going to use and remove...

Is it possible only to buy receiver end if I am already using EZ Bridge LT+ product?


Yes, it is possible. The second receiving antenna is what we call EZ Go+ There are 2 main requirements so you can have another receiver in your EZ Bridge setup. Make sure the 2nd receiving antenna would be within a 35-degree beamwidth of the...

How do I reconfigure my EZBR-0214+ for side A and B firmware


If you accidentally erased the firmware on your bridge you can visit Click here in order to get the side A and B firmware. When you download the firmware to a computer you will need to open the antenna A GUI. You can get to it by connecting...

EZ-Bridge LT+ TyconOS Wiki


Status               Overview The overview page contains link status information and other pertinent info regarding active Wifi and Lan interfaces. This is the goto page for system status. Routes Displays the current...

Will my speed slow down at extended distances?


At the recommended max distance with a clear line-of-sight and minimal external interference, the EZ-Bridge® will perform as advertised. However, if there are obstacles in the path or excessive external wireless interference or multipath...

Is it better to use a 2.4GHz or 5GHz EZ-Bridge?


5GHz Bridges absolutely need to have a clear line of site.  With 2.4GHz Bridges, a clear line of site is still the absolute best, but it is a little more forgiving with line of site issues.  You may be able to get away with a few trees in the...

Can I power a second device off my EZ-Bridge-LT+?


The RJ45 connectors on the LT+ don’t have PoE output capability, but you can use a 5.5 x 2.1mm DC Plug Jumper to power up the second EZ-Bridge. Maximum 10W output @ 15-24V DC. Note: The EZ-Bridge requires much less than 10W.

Can I power your EZ-Bridge products from a standard PoE Switch?


It depends on the model. EZBR-Dual-AC can be powered from a standard PoE Switch which is 48V PoE. The EZ-Bridge LT+, HD, and ULTRA require 15V to 24V Passive PoE The EZ-Bridge LT+, HD, and ULTRA ships with a 24V Passive PoE inserter. The...

Can the EZ-Bridge be mounted indoors?


The EZ-Bridge is designed to be used outdoors.  The enclosure and design are weatherproof, and the units offer long life in outdoor environments.    We understand that some people may want to use the units indoors. This is perfectly fine....

How can I connect two separate networks across an EZ-Bridge Ultra?


It is possible to have two separate networks connected through the EZ-Bridge Ultra You can have an EZ-Bridge Ultra connecting a network at the Local side with a network at the Remote side, using two routers, one router (Local) and one Router...

Do I need to be an engineer or technical person to install and operate the EZ-Bridge?


The EZ-Bridge® is plug and play with no setup required. If you can install a wireless router or computer peripheral, you should have no problem with the EZ-Bridge.

How critical is line-of-sight when using the EZ-bridge.


With Wireless Bridges, a clear line of site is always recommended. Any obstructions ie; Trees, Poles, Fences, and Buildings can block or reduce the power of a wireless signal. 5GHz is more sensitive to line of site issues. 2.4Ghz is more...

How do I reset the EZ-Bridge® to factory defaults if I can't open the unit's web page?


Power up the EZ-Bridge® unit. Wait at least 2 minutes for the unit to boot, Press and hold the black reset button (visible inside the bottom of the unit) for 15-20 seconds. WARNING! Don't exceed 25 seconds or the firmware will be...

How do I access the EZ-Bridge® to change settings?


The EZ-Bridge® comes from the factory programmed to be plug and play. If the units are installed and powered up, they will automatically bridge the networks.  If you want to change settings for any reason, you should refer to the user guide...

Can I have a router on both sides of the EZ-Bridge® link?


Yes, on the internet side of the link, the EZ-Bridge® would be connected to one of the LAN ports on the main router. On the remote side of the link the EZ-Bridge® would connect to the WAN or INTERNET port on the router. The remote side router...

I can't open the EZ-Bridge® unit's web page with my browser


To open the EZ-Bridge® web page with your browser you need to type in the IP address of the EZ-Bridge® into the address bar of a web browser (like Firefox, Chrome, etc.). Your computer must be on the same subnet as the EZ-Bridge®. If the...

Are the EZ-Bridge systems shipped complete with everything I need?


Systems are shipped with everything that is needed except the mounting pole or tower and CAT5 cables (if needed to interconnect equipment). The systems ship with 2 antennas with pole mount brackets, Power Over Ethernet Power Supplies and...

What is the function of the LED's on the LT


The meaning of the LED's on the EZ-Bridge LT+ is outlined below

Can I get some help on QOS settings using WISPOS firmware?


For the bandwidth to be used by anyone when not used by higher priorities you should check the "Bandwidth Borrowed" checkbox. Then there is the "Max Throughput" field which, as the name suggests, sets the maximum throughput that will be allowed...

How can I know if my bridges are communicating?


Caution: When plugging and unplugging Ethernet cables between the POE inserter and the Bridge, do so ONLY when POE inserter is unplugged from the AC socket. Plugging/unplugging CAT5/6 cables while the POE inserter is powered can permanently...

What do I need to supply when installing the EZ-Bridge® system?


You will need CAT5/6 Ethernet cable to go between the Power Supply/PoE Inserter and the EZ-Bridge Antenna. Cable must have all 8 wires.  If you purchase the HD EZ-Bridge system, 75' outdoor shielded cables are included. We recommend shielded...

What if I don't have good line-of-sight between my locations? How critical is line of sight?


At under 1/4 mile the EZ-Bridge® is powerful enough that good line of sight isn't very important. Over 1 mile, it is important to have good line of sight between the two units. Shooting through a couple of trees won't have much effect on...

What is the bandwidth / speed capability of the different EZ-Bridge® models?


EZ-Bridge® Dual-AC Up to 866Mbps EZ-Bridge® LT2+ Up to 100Mbps EZ-Bridge® LT5+ Up to 100Mbps EZ-Bridge® Ultra Up to 100Mbps

What is the maximum range of the different EZ-Bridge® units


The LT and LT+ models have a range of up to 3 miles with good line of site. The Ultra 5 has a range of up to 4 miles with a good line of sight. The Ultra 2 has a range of up to 8 miles with a good line of sight.

What is the optimum signal strength dBm for best performance?


On the status or overview page there is a signal strength meter which displays signal strength in dBm. The optimum is between -40 and -60 dBm. This is the range where you will see peak performance. At -80 to -90dBm the units will have a difficult...

What makes the HD model different?


The HD model comes with Power over Ethernet inserter/power supplies with built in Ethernet and PoE surge protection. They also come with two 75' Shielded and outdoor rated CAT5 cable assemblies. These protections help to ensure long life in...

Which Ethernet port on EZ-Bridge-LT+ do I plug into?


You can plug into either port.  The ports are identical. Both ports will power the bridge via 12-24V Passive PoE. The second port is included in case you have multiple Ethernet devices that need to be connected.
Join Our Waitlist We will inform you when the product arrives in stock. Please leave your valid email address below.